Roadtrek

Roadtrek

Wednesday, August 19, 2015

Don't Lose Your Water Heater Door

If you have a Roadtrek - or any RV - with a Suburban (or with some other RVs Atwood) hot water heater on the outside wall of the van (behind where your water heater tank is located) there is a panel door with vents to access your hot water heater to empty the tank and/or change the anode rod (if you have a Suburban as many Roadtreks do). From what some of our readers have told me and what I have seen on many forums, these doors can come off and get lost. When they do you are left with the not inexpensive task of replacing it and then painting it to match the exterior color of the RV.

I recently read a comment from someone who said losing this door is an "RV right of passage". What baloney! Don't lose it and this is how to prevent that - and for less than four dollars.

Now, I cannot take credit for this idea. I read about this idea in a magazine on motorhomes, but I have modified the idea. Here we go.

First it is important to understand - if you don't have an RV yet - how this door "locks" in place. At top of the door in the center there is a vertical slot. From behind that slot a plastic ring on a flexible strap comes through the slot and then is turned horizontally and then pushed down so that it lies flat against the door. IF this remains this way the door will not come off. Why would it not lie flat? If the strap starts to lose its elasticity, if someone maliciously comes along and turns the ring vertically, or if vibrations cause the ring to lift and turn - all reasons why the door may fall off - and I am sure there are many others.

The simplest solution would be to put a hasp lock through the ring and lock it but then you will have "BANG, BANG" as you drive down the road with the lock hitting the side of the door with every bump. Not really a good idea.

What the magazine suggested was to take a screw and nut and put it through the ring, preventing the ring from coming through the slot without removing the nut and screw. Nice idea, but I could see the screw also bouncing around if it was loose in the ring and also scratching the paint on the door. So I modified this idea for my Roadtrek by using a nylon screw and nut. You need to buy two things - both found in Lowes - not on the wall with screws and nuts but in the specialty parts drawers in the same aisle of the store.


You can see the parts number, sizes and descriptions on the packages above. You want a 1/4-20 X 1/2 nylon screw. With that you want matching 1/4-20 nylon nuts. You get two screws in a package and 4 nuts in a package. Each package costs less than $2.00. Total cost for the whole project is less than $4.00. The 1/4 is the thickness of the screw. The 20 is the thread on the screw. The 1/2 is the length of the screw.

I tried a longer screw and I also tried a matching wing nut to the screw shown above. The longer than 1/2 inch screw was too long and the ring would not sit against the door when it was in place. The wing nut was much too big - none smaller were to be had - and that prevented the ring from sitting flat against the door. With anything through the ring, the ring will not sit exactly flat but with the right combination shown here, you can get the ring as flat as possible with little chance that it will stick out too far from the side of the van and become a problem.


 Here is what you do - oh, so simple!  Turn the ring vertically. Put the screw through the ring. The head of this screw is bigger than the opening in the ring so it will not pull through and stop flush. Put the nut on the end of the screw and tighten it on - no screw driver - use your hand and for the last turn gently use a coin. Do not screw it so tight that it will break the ring. That would be a very expensive mistake. Just tighten the nut until it meets the ring and it will not come off. Turn the ring horizontally as much as it goes - you will see this in the photo below, and let it stay on an angle. Done!


To remove this to open the door, just unscrew the nut and remove the screw. If the nut seems tight, use a coin in the slot of the screw to turn the screw to open it as you hold the nut with your fingers. It should be no effort to unscrew the nut - but after some time after putting it on, it does seem to tighten more on the screw - though not on the ring.

Yes, there is still the possibility of someone stealing the door. If they really want it there is not much you can do to stop that as the ring could just be broken even with a lock through it. But with this, you will cut down the possibility of losing this door by - how much? 90%? More? Better than nothing is always good! And the nylon will not scratch the paint.














14 comments:

  1. Oh, I'm so doing this. Thanks for sharing!

    ReplyDelete
  2. Lost mine this summer as a repairman didn't get it latched and I failed to double check. We went 3/4 across the country with it naked, until we arrived at a destination where I had a new door delivered from Amazon. This is a much cheaper solution!

    ReplyDelete
    Replies
    1. I can't find water heater door of suburban nt 16 seq in Amazon

      Delete
    2. Search for this part. If it is not on Amazon, it should come up on some RV supplies website. The Suburban is common to many RVs - Suburban 6261APW Water Heater Door or for the flush mount - SUBURBAN MFG Part Number: 6255APW

      Delete
  3. VERY helpful! Lost one, and I'm not going to lose another!

    ReplyDelete
  4. My door just fell off for the first time "somehow" at the hand carwash - doing this! Thanks!

    ReplyDelete
  5. Losing the door is something that this newbie had not thought of. Thanks for the tip! Will be implementing this as soon as I can get the screw and nut.

    ReplyDelete
  6. Thank you! I appreciate you posting the specifics of the nut and screw--even where they were located at Lowes! We lost our water heater door on our last trip and had to buy a new one--not cheap! I've been searching for a latch or something--most were metal that would have scratched the door. This is PERFECT!

    ReplyDelete
  7. We lost ours driving home from the seller's place. I assume they winterized it and neglected to turn the latch all the way. There's a new one coming from Amazon shortly and I will employ this terrific trick to secure it. Thanks!

    ReplyDelete
  8. This is a great preventative! Thank you, Robert!

    ReplyDelete
  9. Ugh, just happened to myself. You wouldn't happen to know the part name besides "water heater access panel" or some such?

    ReplyDelete
    Replies
    1. You should be able to find it by searching for a Suburban 6261APW Water Heater Door or for the flush mount - SUBURBAN MFG Part Number: 6255APW.

      Delete
  10. I lost 2 on other rv;s so as soon as I got my roadtrek I put a tiny little lock on it. I like your idea because it doesnt need a key.

    ReplyDelete
  11. After reading this, I just put a small zip tie from the grate through the ring and pulled it flat. I will have to cut it to get in and replace it, but I just changed the pressure valve and will not likely need in again soon. Plus I carry these in my parts kit.

    ReplyDelete